HD Video Balun HD-CVI TVI AHD & CVBS analog camera CCTV Video up to 440m (PAIR)
(Product code: DH-HDP4102 | EAN-13: )
Average Customer Rating:
Currently not rated
The DH-HDP4102 video balun is a passive (non-amplified) device that allows the transmission of real-time CCTV HD video signal via cost-effective Unshielded Twisted Paired (UTP) cable. Baseband (composite) signals of any type are supported.
The DH-HDP4102 is compatible with all HD-TVI, HD-CVI, AHD & CVBS analog cameras.
Male BNC of the DH-HDP4102 allows connection directly to the camera and DVR. Screw terminals of the DH-HDP4102 allows easy connection of UTP cable output. Used in pairs, the DH-HDP4102 eliminates costly and bulky coaxial cable.
The superior interference rejection and low emissions of the DH-HDP4102 allow video signals to coexist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of a shared or existing cable plant. With built-in TVS(Transient Voltage Suppressors) for surge protection, damaging voltage spike problems are eliminated.
Real-time transmission over UTP cat5e/6
No power required
NTSC, PAL & SECAM video format compatible
Compatible with all HD-TVI, HD-CVI, AHD & CVBS analog cameras
Color video max up to 440m(1443ft) for HD-CVI 720P camera, If you adjust saturation of DVR, max up to 480m(1574ft)
Color video max up to 220m(721ft) for HD-CVI 1080P camera
Color video max up to 190m(623ft) for Hikvision TVI 720P camera
Color video max up to 190m(623ft) for Hikvision TVI 1080P camera
Color video max up to 230m(754ft) for TVT HD-TVI 1080P camera
Color video max up to 300m(984ft) for AHD 720P camera
Color video max up to 240m(787ft) for AHD 960P camera
Color video max up to 220m(721ft) for AHD 1080P camera
Male BNC connector
Two screw terminals connection for UTP cable
Built-in TVS (Transient Voltage Suppressor)for surge protection
Wave Filter Design, Anti-Static Design
Lightning protection design Grade: III
60 dB crosstalk and noise immunity
Exceptional interference rejection
ABS engineering plastic housing
Wire and Cable Recommendations
The DH-HDP4102 is recommended to use with Unshielded Twisted Paired (UTP) wiring from 24AWG through 22AWG,Individually shielded pairs should be avoided, as they reduce the operating range of the systems drastically. Multi-pair cable (25-pair or more) with an overall shield are acceptable. Video signals can coexist in the same wire bundle as telephone, datacom, or low-voltages power circuits. While video may be routed through telephone punch-down block terminals, any bridge-taps, also called T-taps and any resistive, capacitive or inductive devices MUST BE removed from the pair.
Model
DH-HDP4102
Product Name
Single Channel HD Passive Video Balun
Applied Devices
CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equipment
Video
Video Format
PAL, NTSC, SECAM
Operating Frequency
DC to 42MHz
Max Distance
HD-TVI 720P: 230m
HD-CVI 720P: 440m
AHD 720P: 320m
HD-TVI 1080P: 250m
HD-CVI 1080P: 240m
AHD 960P: 330m
Common-mode/Differential-mode rejection
15KHz to 42MHz 60 dB typ
Impedance
Coax, Male BNC 75Ω unbalanced
UTP, screw terminal 100Ω balanced
Attenuation
1.5 dB typ Max
Wire Type
Network Wiring
One Unshielded Twisted Pair (for each video signal) 24-16 AWG (0.5-1.31mm)