HD Video + Power Balun HD-CVI TVI AHD & CVBS CCTV Video upto 440m (pair)
(Product code: DH-HD4301VP | EAN-13: )
Average Customer Rating:
Currently not rated
The DH-HD4301VP is video & power transmitter and receiver that allows the transmission of real-time CCTV HD video and power signal via cost-effective unshielded Twisted Paired (UTP) cable. Baseband (composite) signals of any type are supported.
The DH-HD4301VP is compatible with all HD-TVI, HD-CVI, AHD & CVBS analog cameras. Used in pairs, DH-HD4301VP eliminates costly and bulky coaxial cable.
The superior interference rejection and low emissions of the DH-HD4301VP allow video & power signals to coexist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of a shared or existing cable plant. The DH-HD4301VPT and DH-4301VPR is built-in surge suppressor to protect video equipment against damaging
voltage spikes. Its crosstalk and noise immunity ensure quality video signals.
Real-time transmission over UTP cat5e/6
No power required
NTSC, PAL & SECAM video format compatible
Compatible with all HD-TVI, HD-CVI, AHD & CVBS analog cameras
Color video max up to 440m(1443ft) for HD-CVI 720P camera, If you adjust saturation of DVR, max up to 480m(1574ft)
Color video max up to 220m(721ft) for HD-CVI 1080P camera
Color video max up to 190m(623ft) for Hikvision TVI 720P camera
Color video max up to 190m(623ft) for Hikvision TVI 1080P camera
Color video max up to 210m(688ft) for TVT HD-TVI 720P camera
Color video max up to 230m(754ft) for TVT HD-TVI 1080P camera
Color video max up to 300m(984ft) for AHD 720P camera
Color video max up to 240m(787ft) for AHD 960P camera
Color video max up to 220m(721ft) for AHD 1080P camera
Male BNC with extended 5.9inch(150mm)mini-coax pigtail
RJ45 Jack for UTP cable
Built-in TVS (Transient Voltage Suppressor)for surge protection
Wave Filter Design, Anti-Static Design
Lightning protection design Grade: III
60 dB crosstalk and noise immunity
Exceptional interference rejection
ABS engineering plastic housing
Wire and Cable Recommendations
The DH-HD4301VP is recommended to use with Unshielded Twisted Paired (UTP) wiring from 24AWG through 22AWG..Individually shielded pairs should be avoided, as they reduce the operating range of the systems drastically. Multi-pair cable (25-pair or more) with an overall shield are acceptable. Video signals can coexist in the same wire bundle as telephone, datacom, or low-voltages power circuits. While video may be routed through telephone punch-down block terminals, any bridge-taps, also called T-taps and any resistive, capacitive or inductive devices MUST BE removed from the pair.
For more specific information regarding wire types, gauges and proper installation techniques, please contact us for technical assistance.
Model
DH-HD4301VP
Product Name
Single Channel HD Video & Power Transmitter & Receiver
Applied Devices
CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equipment
Video
Video Format
PAL, NTSC, SECAM
Operating Frequency
DC to 42MHz
Max Distance
HD-TVI 720P: 230m,
HD-CVI 720P: 440m,
AHD 720P: 320m,
HD-TVI 1080P: 200m
HD-CVI 1080P: 240m
AHD 960P: 330m
Common-mode/Differential-mode rejection
15KHz to 42MHz 60 dB typ
Impedance
Coax, Male BNC 75Ω unbalanced UTP, RJ45 100Ω balanced
Attenuation
1.5 dB typ Max
Wire Type
Network Wiring
One Unshielded Twisted Pair (for each video signal) 24-16 AWG (0.5-1.31mm)
Category Type
2 or better
Impedance
100 ± 20 ohms
DC Loop Resistance
52 ohms per 1,000ft (18 ohms per 100m)
Differential Capacitance
19 pF/ft max (62 pF/m max)
Power
Power Input
No external power required
Power transmission
12V/24V,DC/AC, via UTP cat5e/6. please refer to power distance chart above
.png)
